ZIPPY Flightmax 4000mAh 2S1P 25C Car Lipoly (ROAR APPROVED)

2 year plus update Link

I heard really good things about this pack and with them being the cheapest hardcase packs ($15.50) on hobby kings site I just had to give them a try and see what they were made of .
Well I started by checking the voltages when I got these in . One pack was at a little down with cell 1 at 3.84 and cell 2 at 3.85 . The second pack which by the warranty number was a bit newer was at 3.86 on both cells so in my opinion things looked pretty good from the start . I then solder on a couple of dean's style T-connectors and proceeded to charge the packs up . After handling the wiring harness a bit I decided I didn't want to use the stock harness for running in my car or for fast charging and made 2 more harnesses minus the balance plug as it could be damaged . After the packs got done Balance charging I decided to take them for a spin and yes virginia these packs do have some punch dare I say more than the Turnigy 30C 4000mah packs I tried hmm further testing is needed because despite feeling Zippy these packs did warm up a hair bit but that may be due to this being there first outing . After I get a few more cycles on these and the Turnigys I will be updating these post .

This pack has a Relative Amp 25C x 4A = 100rA 
$15.50 / 100rA = 0.155cE the lower the number the Cost Effective




Where to buy it
ZIPPY Flightmax 4000mAh 2S1P 25C Car Lipoly (ROAR APPROVED)


Manufacturer description:

 Zippy FLIGHTMAX batteries deliver full capacity & discharge as well as being the best value batteries in the hobby market today!

Spec.
Capacity: 4000mAh
Voltage: 2S1P / 2 Cell / 7.4v
Discharge: 25C Constant / 30C Burst
Weight: 235g (including wire, plug & shrink wrap)
Dimensions: 138x47x23mm
Balance Plug: JST-XH
Discharge plug: 4mm Bullet-connector to your own custom plug

UPDATE Latest stock has improved soldering and tab joins. Removing previous issues related to 'cold solder' breakages.

Now officialy approved by ROAR for race use!

PRODUCT ID: Z40002S-25

Parallel charging Board for 6 packs 2~6S (T Connector) (USA Warehouse)

Well I got this from the US Warehouse with my last order . I planned on using this to charge my smaller packs for my 1/16th scale and 1/18th scale cars but I have found that this also handy for slow charging my larger packs in bulk . So far I Have no complaints especially when I could have paid a lot more for a very similar product and since I won't be using this to much I think why spend money I don't have.

For those that don't understand the benefits of using this device I will attempt to explain .
If you have a charger that has the ability to charge at a higher and rate then your batteries are recommended to be charged at you are wasting precious time . My personal example would be my GT power X-charger C6 It is rated to charge at up to 6.0 amps when charging a 2s lipo battery pack  rated at 1500mah and a 1c charge rate .  What happens is that this board connects the batteries in parallel to each other and then connects to the charger . The charger only sees the batteries as one big battery when connected like this and when the batteries are connected in parallel the charge rate is divided among them . So if I connect 4 batteries rated at 1500mah and charge them at a 1C  rate then I will be using the full potential of my battery charger .

Now as my public service announcement :

All Batteries That You Plan To Charge Must Be Of The Same Capacity at the minimum but personally I will Only be charging packs of the same rating from the same manufacturer .  

Manufacturer's description :

Charge SIX (2~6S) lipo packs with same capacity & cell count simultaneously with this parallel charging board.

That means you can charge 6 3S 2200mAh or more at the same time with a standard charger!


Spec.Cell: 2~6SVoltage: 0~22.2VDCMax current: 30ABattery: 6 packs same capacity & cell countConnector: T Connector/Jst-xh

PRODUCT ID: 9171000064

Where to buy :
Parallel charging Board for 6 packs 2~6S (T Connector) (USA Warehouse)

News flash Turnigy Stadium King 2wd truggy / ZD Racing ZMT-10 Brushed motor model is 3s capable

Well I decided just for giggles to see is a 3s lipo would burn up the esc for my ZMT-10 and was surprised to find out that the esc recognized that the pack was a 3s . Normally the esc ( currently in a Clodbuster ) Goes through its little beep sequence and I give it little thought but when I hooked up a 3s lipo to the esc I knew something was different instead of the normal BEEP-BEEPBEEP-BEEP IT WENT BEEP-BEEPBEEPBEEP-BEEP signalling that the voltage cut off recognized that the pack was a 3 cell I couldn't believe it . after driving for a bit the esc showed no heat increase so I feel safe in saying this esc is good to go on 3s lipos but I still recommend a lipo alarm as the voltage cut off is too low for my taste.

Hobby King Programming Card for Car ESC (USA Warehouse)

Well it does exactly what it is supposed to do its only downfall is that its construction is primarily a circuit board and card board and it doesn't seem like it would put up with much abuse so I recommend keeping it in a  safe place. I do wish there was a cheat sheet for the buttons as there layout makes it a little hard to remember what the far left and center arrow functions are unless you use it constantly.

According to my research this programing card works with these esc's 

Hobby King Brushless Car ESC 100A w/ Reverse (Upgrade version 
PRODUCT ID: HK-100A 

HobbyKing Brushless Car ESC 60A w/ Reverse 
PRODUCT ID: HK-60A 

HobbyKing Brushless Car ESC 45A w/ Reverse 
PRODUCT ID: HK-45A 

HobbyKing Brushless Car ESC 30A w/ Reverse 
PRODUCT ID: HK-30A










Where to get it .
Hobby King Programming Card for Car ESC (USA Warehouse)

Manufacturer description :

Hobby King  Programming Card for Car ESC 

LED programming card for Hobby King 100A car ESC.

PRODUCT ID: HKProg-card